Swing tags on overtrousers are full of numbers: 10,000mm, 20,000g/m²/24h, RET 12, EN 343 Class 3. They look precise, and the tests behind them are real, but each number answers a narrow question under laboratory conditions. This post explains what the main tests measure, what the standards actually say, and the questions the labels cannot answer for you.
Hydrostatic head: how waterproof is the fabric?
The hydrostatic head test is described in the international standard ISO 811 (published in Europe as EN ISO 811, and earlier as EN 20811). A sample of fabric is clamped under a reservoir of water and the water pressure on one face is increased steadily. The test ends when drops of water have come through the fabric in three places, and the pressure at that point is the result.
Outdoor brands usually express that pressure as the height of a column of water in millimetres, so "10,000mm" means the fabric resisted the pressure of a 10-metre column before water came through. The standard itself expresses results as pressure, and you will sometimes see pascals (Pa), kilopascals or millibars instead. They are just different units for the same thing: one millimetre of water is about 9.8 pascals.
Points worth knowing:
- It is a fabric test. A hydrostatic head figure usually tells you about the fabric, not the finished trousers. Seams, zips and the waist are separate questions.
- It is usually done on new fabric. Real trousers are flexed at the knee, rubbed at the inner leg and pressed onto wet seats. Wear can reduce performance over time.
- Pressure on legs can be high. Kneeling and sitting concentrate pressure in a small area, which is one reason trousers benefit from more headroom than a figure for falling rain alone might suggest.
The buying guide gives rough bands for what different figures tend to suit. Treat them as a rough guide, not a rule.
Breathability: two different measurements
Breathability is about how readily water vapour from sweat passes out through the fabric. Two kinds of number are common, and they cannot be converted into each other.
MVTR (grams per square metre per 24 hours)
Moisture vapour transmission rate measures how much water vapour passes through a square metre of fabric in a day. Higher means more breathable. There are several different test methods, including the "cup" methods in ASTM E96 and the Japanese standard JIS L 1099, and they can produce very different numbers for the same fabric. A label that gives an MVTR figure without saying which method was used is hard to compare with anything.
RET (resistance to evaporative heat transfer)
RET is measured to ISO 11092, using a heated, "sweating" plate that mimics skin. It measures how much the fabric resists evaporative heat loss, in units of square metres times pascals per watt. Lower means more breathable. Because ISO 11092 is a single defined method, RET figures tested to it are easier to compare than MVTR figures, although results still depend on the lab and the sample.
Neither number accounts for wind, ventilation zips, how hard you are working, or the fact that a fabric whose outer face is soaked with water breathes much less. That last point is why keeping the water repellent finish working matters so much.
EN 343: the standard for rainwear as protective clothing
EN 343 is the European standard for protective clothing against rain. The current edition is EN 343:2019, and plenty of garments are still labelled to the earlier 2003 edition. It is used mainly for workwear and PPE, so you are more likely to see it on site and farm overtrousers than on walking trousers. Unlike a single fabric figure, it assesses the garment, including its seams.
A garment certified to EN 343 is marked with two class numbers:
- Water penetration resistance. Based on hydrostatic pressure tests of the material and seams. In the 2019 edition this runs from Class 1 to Class 4; the higher classes require the material to keep its resistance after pretreatments designed to imitate wear and cleaning.
- Water vapour resistance (breathability). Based on RET. Again Class 1 to Class 4 in the 2019 edition, with Class 4 the most breathable. For Class 1, the standard calls for a recommended limit on continuous wearing time, which should appear in the maker's user information.
Older garments certified to the 2003 edition use Classes 1 to 3 for each property. In all editions, higher is better for both numbers. If you buy overtrousers for work, check which edition and classes your employer or site rules require; our work & hi-vis guide covers this alongside EN ISO 20471 for visibility.
What labels do not tell you
Outside PPE, makers choose which figures to publish and how to test them. When comparing pairs, look beyond the headline number:
- Seams. "Fully taped" or "sealed" seams matter more than a high fabric figure. "Critically taped" usually means only some seams are sealed.
- Construction. 2, 2.5 and 3-layer fabrics differ in durability and feel, which affects how long that headline figure lasts in use.
- Zips and cuffs. Storm flaps, coated zips and adjustable ankles all affect how much water gets in at the edges.
- The water repellent finish. No standard figure on the tag tells you how long the DWR will last before the fabric wets out.
- Method. Compare MVTR figures only when the same method was used, ideally within one brand's range.
A sensible way to use the numbers
- Decide what you need first: how long you will be out in rain, how hard you will be working and whether you will kneel or sit.
- Use hydrostatic head as a rough filter for waterproofing, and check the seams are fully taped.
- If you work hard in them, look for an RET figure (lower is better) or a high EN 343 breathability class, and for zips you can open.
- For work, follow your site's EN 343 and visibility requirements.
If you mainly stand still, as anglers and spectators often do, a tougher, less breathable fabric can be a better buy than a high breathability figure. See the fishing guide for that trade-off. For a wider look at waterproof kit for wet weekends away, Camping.me.uk's waterproofs page is a useful companion.